astm a709 grade hps50w specs

astm a709 grade hps50w specs

astm a709 grade hps50w specs Related introduction

  1. ASTM-A709 | Standard Specification for Structural Steel , astm a709 grade hps50w specs

  2. ASTM A709 Grade 50S|A709 Gr.50S steel plate__Steel Supplier

  3. ASTM A709-A709M | Steel Plate, Steel Bar, Steel Tubes

    ASTM A709/A709M specification covers carbon and high-strength low alloy steel structural shapes, plates and bars, and quenched and tempered alloy steel for structural plates intended for use in bridges. ASTM A709/A709M Standard main steel grade: ASTM A709 Grade 36, 50, 50S, 50W, HPS50W (A709GR36, A709GR50, A709GR50S, A709GR50W, A709GRHPS50W)

  4. ASTM A709/A709M-17e1 - Standard Specification for , astm a709 grade hps50w specs

  5. ASTM A709/A709M-18 - Standard Specification for

  6. Plate - ArcelorMittal USA

    Committee. The first of these steels is ASTM A709 Grade HPS 70W (HPS 485W), known simply as HPS 70W. HPS 70W is defined as steel plate that has: A minimum yield strength of 70 ksi (485 MPa) High levels of fracture toughness (zone 3 minimum) Reduced preheat requirements for welding Improved weathering properties per ASTM G101

  7. Steel grades according to American standards - A36,

    Grade 60 415 [60] 520 [75] 16 18 Grade 65 450 [65] 550 [80] 15 17 A588 - 04 Grade B 345 [50] 485 [70] 18 21 Grade C 345 [50] 485 [70] 18 21 A709 - 04a Grade 36 250 [36] 400-550 [58-80] 20 21 Grade 50 345 [50] 450 [65] 18 21 Grade 50S 345-450 [50-65] 450 [65] 0.85 18 21 A913 - 04 Grade 50 345 [50] 450 [65] 0.85

  8. A709 Structural, Carbon & HSLA Steel Plate - Chapel Steel

    Chapel Steel stocks A709 Grade 36, A709 Grade 50 and A709 Grade 50W. These grades are often specified with Charpy tests referencing the specific zone or lowest anticipated service temperature. The Charpy tests are specified as non-fracture critical, which is a per-heat test (frequency "H"), or fracture critical, which is a per-plate test (Frequency "P").

  9. ASTM A572 Grade 50, Type 2 A709 Grade 50 - Ranger Steel

    ASTM A572 Grade 50, Type 2 A709 Grade 50 AASHTO M270 Used in Bridges, Buildings, Construction Equipment Machinery, Transmission Towers, Truck Parts, Towers, and Freight Cars. It is a higher yield and tensile strength than A36.

  10. ASTM A709 - SSAB

    The ASTM A709 is the Standard Specification for Structural Steel for Bridges and encompasses carbon, high-strength low-alloy, and quenched and tempered alloy steels used as structural plates in the construction of bridges. SSAB offers the following five grades of A709; 36, 50, 50W, HPS 50W and HPS 70W.

  11. ASTM A709 / A709M - 13 Standard Specification for , astm a709 grade hps50w specs

    ASTM Standards. A6/A6M Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling. A36/A36M Specification for Carbon Structural Steel. A370 Test Methods and Definitions for Mechanical Testing of Steel Products. A572/A572M Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel

  12. ASTM A709 / A709M - 18 Standard Specification for , astm a709 grade hps50w specs

  13. ASTM A709 Grade HPS 50W & 70W | Leeco Steel, LLC

    ASTM A709 grade HPS steel plate is primarily used in the manufacture of bridges. The grades HPS 50W and HPS 70W are higher performing grades for extreme climates, where temperature fluctuations are


    ASTM Standard Specification A709/A709M, Section 1.3, states, When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. See Appendix X3 of Specification A6/A6M for information on weldability. ASTM A6/A6M, Section X3, Weldability of

  15. High Performance Steel Designers' Guide

    The chemistry for HPS 50W grade steel is the same as HPS 70W shown in the table above. ASTM A709 Grade HPS 50W is contained in A709-01 and is produced using conventional hot- rolling or controlled rolling up to 4" thick in lengths similar to Grade 50W steel.

  16. HPS 50W: Steels for Bridges - ArcelorMittal USA

    HPS 50W: Steels for Bridges ASTM A709-01 first added grade HPS 50W. This high performance bridge steel has the identical chemistry as HPS 70W. It will most often be produced by as-rolled or control-rolled practices. ASTM A709 also allows it to be Thermo-Mechanical Controlled Processed (TMCP), with or without accelerated cooling, normalized, quenched

  17. Steel Plate for Bridges - EVRAZ North America

    HPS 50W 0.375 - 4.00 Up to 152 Up to 1020** 0.375 - 4.00 HPS 70W 0.375 - 0.750 Up to 120 Inquire 0.375 - 0.750 Plate Specifications Data Sheet Overview: EVRAZ North America offers high-quality bridge plate produced in the United States that meets the requirements of AASHTO specification M270, ASTM A709 and customized structural plate , astm a709 grade hps50w specs

Online Consultation